Sysop@vitcompany.com: 1 revision

2015-03-10T11:21:46Z

1 revision

New page

==Recognition Servers Management==

After the installation, VIT Recognition Server is available for future configuration in Milestone Management Application, Surveillance Server – Advanced Configuration - MIP Plug-ins – VIT Analytic Service section. No additional software is required for VIT Recognition Server management.
 

List of Recognition Serves is available in Recognition Servers section of Milestone Management Application property tree.
 

To see all Recognition servers, available in the system, it is necessary to select '''Recognition Servers''' section. After that table with list of all Recognition servers will be shown at the right part of the application (see fig. ''Recognition Servers. List of all available servers'').
 

 
[[File:MAEnterprise32.png|thumb|center|Recognition Servers. List of all available servers| 900px]]
 

Table columns properties:

:* '''Enabled''' – mark in this field shows, if the server can be used;
:* '''Name''' – Recognition server’s name;
:* '''ID''' – server’s ID that generated automatically when server created; can’t be edited;
:* '''Kind''' – ID’s type; can’t be edited.

To get information about some specific server it is necessary to select its name in the servers list. After that table with information about selected server will be shown at the right part of the application (see fig. ''Recognition Servers. Information about selected server''). In addition in properties tree will be shown section with recognition channels, connected to specified Recognition server.

 
[[File:MAEnterprise33.png|thumb|center|Recognition Servers. Information about selected server| 900px]]
 

To get information about all recognition channels, connected to specified Recognition server it is necessary to select '''Channels''' section, associated with specified Recognition server. After that table with information about channels will be shown at the right part of the application (see fig. ''Recognition Servers. Information about server’s channels'').

 
[[File:MAEnterprise34.png|thumb|center|Recognition Servers. Information about server’s channels| 900px]]
 

To get information about specified channel it is necessary to select its name in the channels list. After that table with information about channel will be shown at the right part of the application (see fig. ''Recognition Servers. Information about channel'').

 
[[File:MAEnterprise35.png|thumb|center|Recognition Servers. Information about channel| 900px]]
 

===New Recognition Server Creation===

To create a new Recognition server it is necessary to perform the following steps:
 
# click with right mouse button on the '''Recognition Servers''' section and select '''Create New''' in the context menu (see fig. ''Recognition Servers. New Source Server Creation'');
# paste the server’s name in the pop-up window and press the OK button (see fig. ''Recognition Servers. Server naming'').

 
[[File:MAEnterprise36.png|thumb|center|Recognition Servers. New Source Server Creation| 900px]]
 
[[File:MAEnterprise37.png|thumb|center|Recognition Servers. Server naming| 900px]]
 

At this point new Recognition server is created. It is available for future management in the servers list. Server’s settings such as logging path can be set at the server’s side with the help of LPR Server Manager. To connect and tune recognition cannels Milestone Management Application is used.

===Recognition Server Configuration===
To configure Recognition server’s parameters it is necessary to double click on the specific row at the servers table. After that pop-up window with server’s parameters that are available for editing, will be shown (see fig. ''Recognition Servers. Recognition Server’s parameters window'').

 
[[File:MAEnterprise38.png|thumb|center|Recognition Servers. Recognition Server’s parameters window| 900px]]
 

Table columns properties:
 
:* '''Enabled''' – flag in this field defines if the server available for usage;
:* '''Name''' – name of the Recognition server;
:* '''ID''' – server’s ID that generated automatically when server created; can’t be edited;
:* '''Kind''' – ID’s type; can’t be edited.

===Recognition Server Deletion===
To delete existing Recognition server it is necessary to perform the following steps:
 
# click with right mouse button on the name of the specified Recognition server and select '''Delete''' in the context menu (see fig. ''Recognition Servers. Recognition server deletion'');
# confirm deletion in the pop-up window (see fig. ''Recognition Servers. Confirmation of deletion'').
 

[[File:MAEnterprise39.png|thumb|center|Recognition Servers. Recognition server deletion| 900px]]
 
[[File:MAEnterprise40.png|thumb|center|Recognition Servers. Confirmation of deletion| 900px]]
 

==Recognition Channels Management==

Each Recognition channel is connected with one of Recognition servers. To get information about some specific channel it is necessary to select its name in the channels list (see fig. ''Recognition Servers. Information about selected channe''l):
 
:* in Channels section that is associated with specified server – if it is known to which server channel connected;
:* in general Channels section – if there is no information to which server channel connected.

 
[[File:MAEnterprise41.png|thumb|center|Recognition Servers. Information about channels| 900px]]
 

Table columns properties:
 
:* '''Enabled''' – checked field shows, if the channel can be used;
:* '''Name''' – channel’s name;
:* '''Channel type''' – channel’s type;
:* '''Source server''' – Source server that is used by channel;
:* '''Camera''' – camera that is connected to specified Source server. Video from this camera is used for recognition;
:* '''Target Servers''' – Target server where recognition results are sent.

===New Channel Creation===

To create a new channel it is necessary to perform the following steps:
 
# click with right mouse button on the Channels section that is associated with server where channel must be created and select Create New in the context menu (see fig. ''Recognition Servers. New Channels Creation'')
# paste the channel’s name and type in the pop-up window and press the OK button (see fig. ''Recognition Servers. Channel naming''). Possible channels’ types:
<ol type="a" start="a">
:<li> '''License plate recognition (VitLpr)''' – channel for car license plate recognition;</li>
:<li> '''Van recognition (VitVan)''' – channel for wagon license plate recognition. </li>
</ol>

 
[[File:MAEnterprise42.png|thumb|center|Recognition Servers. New Channels Creation| 900px]]
 
[[File:MAEnterprise43.png|thumb|center|Recognition Servers. Channel naming| 900px]]
 

At this point new channel is created. It is available for future management in the channels list.

===Channel Configuration===

To configure channel’s parameters it is necessary to double click on the specific row at the channels table. After that pop-up window with channel’s parameters that are available for editing, will be shown(see fig. ''Recognition Servers. Channel’s parameters window'').

 
[[File:MAEnterprise44.png|thumb|center|Recognition Servers. Channel’s parameters window| 900px]]
 

Table '''General settings''' columns properties:

:* '''Name''' – channel’s name;
:* '''Enabled''' – flag in this field defines if the channel available for usage;
:* '''License plate templates''' – license number plates’ templates (types of license number plates’ that will be recognized at the specified channel, ordered by country);
:* '''Channel type''' – channel’s type that is defined at the channels creation;
:* '''Recognition server''' – Recognition server where recognition runs;
:* '''Groups''' – group or groups of devices that channel belongs.

====License Number Plate’s Templates====
To define license number plate’s templates it is necessary to perform the following steps:
 
# open tab '''General settings''' at '''Channel settings''' window;
# press the '''Set''' button in column '''License plate templates''' for specified channel or in the table '''Template''', if several channels must recognize license number plates of the same counties;
# select countries and templates in the pop-up window and press the '''OK''' button (see fig. ''Recognition Servers. Recognition templates management'').

 '''''Attention!'''''
----
''Each channel can be managed independently of other channels. For one channel can be selected any number of templates and counties. However, it’s not recommended to select templates that won’t be used – this can reduce the recognition quality. Select only templates that correspond to license plates on the recognizable video. For example, if you use video file with Ukraine cars only, don’t select Russian or USSR or any other template, except Ukraine.''

 
[[File:MAEnterprise45.png|thumb|center|Recognition Servers. Recognition templates management| 900px]]
 

====Connection of Video Source====
To connect video source it is necessary to perform the following:
 
# open tab '''Video source and recognition''' at '''Channel settings''' window;
# select '''Source server''' from servers list in column '''Video source server''' for specified channel. If connection established in column '''Connection status''' word '''connected''' appears (see fig. Recognition Servers. Connection of video source). If that didn’t happened check connection settings for Source;
# select camera from cameras list in column '''Camera''' – video from this camera will be used for recognition.

 
[[File:MAEnterprise46.png|thumb|center|Recognition Servers. Connection of video source| 900px]]
 

====Plate Number Size====
This setting specifies the estimated size of a number plate on the frame; is used to improve system performance by cutting off areas that clearly cannot be license plates.
 

In order to set the plate number size it is necessary to perform the following steps:
 
# open tab '''Video source and recognition''' at '''Channel settings''' window;
# press the '''Edit''' button in column '''Plate size and recognition zone''' for specified channel;
# enable '''Edit size''' option in the pop-up window;
# change rectangles’ sizes on the screen scaling then to the appropriate dimensions (see fig. ''Recognition Servers. Plate number size'');
# press the '''Apply''' button.

 
[[File:MAEnterprise47.png|thumb|center|Recognition Servers. Plate number size| 900px]]
 

Default values: min = 3%, max = 40%.
 

It is especially important to specify the upper bound correctly. If the setting is incorrect, the recognition can performed badly or not performed at all. It is recommended to set the maximum size greater than the actual size on 10-15%. Difference between the minimum and maximum sizes must be around 30%.

====Recognition Zone====

This setting allows selection of the zone in which search for numbers will be performed. This improves the system performance by cutting off areas that clearly cannot contain car images. By default, recognition runs on the entire frame.
 

In order to add the recognition zone it is necessary to perform the following steps:
 
# open tab '''Video source and recognition''' at '''Channel settings''' window;
# press the '''Edit''' button in column '''Plate size and recognition zone''' for specified channel;
# enable '''Edit zone''' option in the pop-up window;
# press the '''New''' button;
# drag the yellow squares located at the edges of the zone on necessary parts. In order to form a polygon, click on viewport by left mouse button - this will add one more vertex (see fig. ''Recognition Servers. Recognition zone'');
# press the '''Apply''' button.

 
[[File:MAEnterprise48.png|thumb|center|Recognition Servers. Recognition zone| 900px]]
 

To change the recognition zone, click on the zone by right mouse button. Recognition zone will be “active”, yellow squares will appear on its tops, available for transfer. By default “active” – is zone that was created last.
 

One can delete a single zone of recognition as well as all zones at once. In order to remove one recognition zone, select the appropriate zone and click '''Delete'''. If you do not select zone, and you just click '''Delete''', then the zone that was added last will be removed.
 

To delete all the recognition zones one must click the button '''Delete all'''.

====Target Server Adding====

In order to add the Target server it is necessary to perform the following steps (see fig. ''Recognition Servers. Target server adding''):
 
# open tab '''Events''' at '''Channel Information''' window;
# select '''Target server''' from servers list in column '''Target server''' for specified channel;
# enable '''Save license plate''' option, if the picture of license plate must be saved in the event;
# enable '''Save car''' option, if the picture of vehicle must be saved in the event;
# if it’s necessary change '''Time correction''' (msec) – this parameter is used for time correction of license plate highlighting frame in Milestone’s archive.

 '''''Attention!'''''
----
''Attention!
Usage of Save license plate and Save car options can course a significant increase of the Data Base size. Don’t enable these options if it isn’t really necessary. But if you’ve enabled them than you need to adjust archive cleaning in Milestone Management Application and control DB size and free space on the disk.''

 
[[File:MAEnterprise49.png|thumb|center|Recognition Servers. Target server adding| 900px]]
 

====Dynamics Settings====

Dynamics means queue of frames processing for getting best recognition result in future. It is necessary to enable these options, unless every frame must be processed separately. This group of options available only for channels with type = '''VitLpr'''.

To define dynamics it is necessary to perform the following steps (see fig. ''Recognition Servers. Dynamics settings''):

# open tab '''Dynamic''' at '''Channel settings''' window;
# click on the channel’s name in channels table to specify channel that will be managed;
# select one of two pre-set profiles or create new one:
<ol type="a" start="a">
:<li> '''Parking''' – vehicle speed is lower than 30 km/h; average optimal settings (steps 5-9) are setting automatically;</li>
:<li> '''Route''' - vehicle speed is higher than 30 km/h; average optimal settings (steps 5-9) are setting automatically;</li>
:<li> '''User settings''' – user must define optimal settings (steps 5-9) by himself;</li>
</ol>
<ol type="1" start="5">
<li> define '''Result delay(sec)''' – time after which first recognition result will be shown;</li>
<li> define '''Check license plate overlap (msec)''' – period in time (in milliseconds) which results can be “glued” to one result in case when license plate will be lost from frame (for example, in case if somebody passed in front of the car);</li>
<li> define '''Minimum interval between cars (sec)''' – period in time (in milliseconds) which results will be “glued” to one result;</li>
<li> define '''Probability threshold recognition''' – percentage of matching of recognition result with standard license plate (corresponding to template: without geometric distortion, using correct font, ect.). Increasing this parameter increases recognition quality, but reduces the number of recognition results. This option available only for channels with type = '''VitLpr'''.</li>
</ol>

 
[[File:MAEnterprise50.png|thumb|center|Recognition Servers. Dynamics settings| 900px]]
 

====Additional Settings====
To define additional settings it is necessary to perform the following steps (see fig. ''Recognition Servers. Additional settings''):
 
# open tab '''Additional settings''' at '''Channel settings''' window;
# click on the channel’s name in channels table to specify channel that will be managed;
# enable '''Analyze inverted plates''' option, if plates with white letters on a black background must be recognized;
# enable '''Send event while car in frame''' option, to send recognition event to Target server while vehicle still on frame. By default event is sent after vehicle leaves the frame. This option available only for channels with type = '''VitLpr''';
# define '''Max number of unresolved symbols''' - maximum number of characters, which allow us to consider the number plate as recognized and record it in the event. This option available only for channels with type = '''VitLpr''';
# define '''Scale factor''' – vertically and horizontally scaling factor that applied to the frame before recognition (for megapixel cameras). Drop-down list of this field makes it possible to set this parameter values from 1 to 4. By manual editing this field scale factor can be set up to 10 points. This option available only for channels with type = '''VitLpr''';
# select from '''Threads per channel''' drop list number of recognition streams recognition (for megapixel cameras). This option available only for channels with type = '''VitLpr'''.

 
[[File:MAEnterprise51.png|thumb|center|Recognition Servers. Additional settings| 900px]]
 

===Channel Deletion===

To delete existing channel it is necessary to perform the following steps:
 
# click with right mouse button on the name of the specified '''channel''' and select '''Delete''' in the context menu (see fig. ''Recognition Servers. Channel deletion'');
# confirm deletion in the pop-up window (see fig. ''Recognition Servers. Confirmation of deletion'').

 
[[File:MAEnterprise52.png|thumb|center|Recognition Servers. Channel deletion| 900px]]
 
[[File:MAEnterprise53.png|thumb|center|Recognition Servers. Confirmation of deletion| 900px]]
 

==Operations with Templates==

Templates are provided to simplify the channels management.
 

'''Template''' – it's a value of a specified parameter or values of a set of parameters which will be applied to all selected servers. Template usage is recommended in a situation when the number of servers with the same parameter or parameters must be configured.
 

To use a template, it is necessary to perform the following steps:
 
# double click on the channel’s name or its settings to activate '''Channel Information''' window;
# open tab with parameters that must be managed;
# paste channel(s) parameters to the '''Template''' table;
# enable '''Apply template''' option for that channels, which it is necessary to apply the parameters, specified at step 3;
# press the '''Set''' button:
<ol type="a" start="a">
:<li> '''Set selected template value on selected channels''' – only active value from the Template table (cell is framed or highlighted) will be applied to the servers specified at the step 4;</li>
:<li> '''Set all template values on selected channels''' - all values from the Template table will be applied to servers specified at step 4.</li>
</ol>

===Example===
There are three channels in a system. Target server and recognition parameters must be defined for them. Default parameters are (see fig. ''Recognition Servers. Default parameters''):
 
:* parameters Save license plate, Save car, Save full frame – «no» (flag disabled);
:* Target server undefined.

 
[[File:MAEnterprise54.png|thumb|center|Recognition Servers. Default parameters| 900px]]
 

Next, parameters must be set:
 
:* same Target server for all channels;
:* Save license plate – «yes», for all channels;
:* Save car – «yes», for the first and the second channels;
:* Save full frame – «yes» only for the first channel.

Possible configuration with use of templates is described below.

====Step 1====
:* enter Target server’s name in the '''Template''' table;
:* enable '''Save license plate''' and '''Save car''' options in the '''Template''' table;
:* disable '''Save full frame''' option in the '''Template''' table;
:* in channels table enable '''Apply template''' option for all channels;
:* press the '''Set''' button for '''Set all template values on selected channels option'''.

The result of the step 1 is shown in the figure ''Recognition Servers. Step 1 of configuration, using template''.

 
[[File:MAEnterprise55.png|thumb|center|Recognition Servers. Step 1 of configuration, using template| 900px]]
 

====Step 2====
:* disable '''Save car''' option in the '''Template''' table;
:* in channels table enable '''Apply template''' option for the third channel;
:* press the '''Set''' button for '''Set selected template value on selected channels''' option.

The result of the step 2 is shown in the figure ''Recognition Servers. Step 2 of configuration, using template''.

 
[[File:MAEnterprise56.png|thumb|center|Recognition Servers. Step 2 of configuration, using template| 900px]]
 

====Step 3====
:* enable Save full frame option for the first channel in channels table.

The result of the step 3 is shown in the figure ''Recognition Servers. Step 3 of configuration, using template''.

 
[[File:MAEnterprise57.png|thumb|center|Recognition Servers. Step 3 of configuration, using template| 900px]]
 

Channel(s) configuration is finished.

[[Category:Documentation for Administrator AutoCode XProtect 2.0 (Enterprise)]]

[[en:Recognition Servers, Enterprise version|Recognition Servers, Enterprise version]]
[[ru: Сервера Аналитики, версия Enterprise|Сервера Аналитики, версия Enterprise]]

Recognition Servers, Enterprise version - Revision history

Sysop@vitcompany.com: 1 revision